Are you hunting for guidance concerning How to Install a Bathtub Yourself?
Setting up a bath tub isn't precisely brain surgery, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bath tub with a new one is additionally a moderately challenging task. If the old tub is easily accessible, the project can move easily; if you have to open up a wall surface to remove the old tub and also position the new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job and fit trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is better to think about using one prior to you start. Chances are you may need an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub and also do not require to change the arrangement of your previous supply of water pipes.
Your tools as well as product list need to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome because of the limited accessibility that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Before moving on to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers are in area in between the tap as well as the sink. Protect the tap in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bath tub until the spirit level reviews degree.
To mount taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water supply as well as examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as likewise inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the bathtub ought to wait till the bath tub has been utilized a minimum of when as this will certainly settle it right into its final setting.
Getting ready for the Installment
To start with, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a stiff seal, triggering the water to pass through the wall between the bathroom as well as the tiling, resulting in problems with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the bath tub with water before securing, to permit the activity experienced when the tub remains in use. The sealant can fracture fairly very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very focused on Tools You Need to Install a New Bathtub and I really hope you appreciated the entire blog posting. For those who appreciated our article plz don't forget to pass it around. Thank-you for your time spent reading it.
Book